HOME

FOTOGRAFIE


reportage
portfolio
foto's herstellen
canvas / doek
fotolijsten

RECYCLE


recycled wearables

SCRAPBOOKEN


scrapbooken
workshops
links
technieken
freebees
layout gallerij

register
contact

MY BLOGS


My life captured in a picture
Multi Photo Layout inspiration

Draw and cut with your Silhouette



For the explanation in English, please scroll down.

Je hebt een bestand nodig met ten minste twee verschillende kleuren lijnen. Ik heb een bestand gebruikt met zwarte en rode lijnen.

- Open het bestand in ROBO Master en click op de [Output Settings] icon (dat is de zesde icon van de linkerkant).
- Ga naar het tabblad [Cutting Settings]
- Click op de knop [Cutline Settings]

Nu zie je dat er twee kleuren lijnen zijn in dit bestand. Zwart en rood. Ik wil dat de zwarte lijnen eerst getekend worden.

- Vink de rode groep uit zodat alleen de zwarte groep aan staat.
- Click [OK]
- Ga naar het tabblad [Print Settings]
- Vink de optie [Print Cut Lines] aan

Nu is het tijd om de pen-holder met de pen in je Silhouette te plaatsen. Als je dat hebt gedaan, zet je de power aan als die nog niet aan stond.

- Click op de knop [Output to Craft ROBO...]

Nu krijg je het gebruikelijke scherm voor het laden van de driver en het starten van het snijden (of in dit geval tekenen.)

- Ik heb mijn snelheid (speed) op 1 gezet en de dichtheid (thickness) op 5. Maar ik denk dat je daar zelf ook even mee moet spelen want veel zal ook afhangen van welke pen je gebruikt. Ik gebruik overigens een Stabilo fijnschrijver.
- Click op de knop [Cut] en de Silhouette gaat aan het tekenen.

Als de Silhouette klaar is met tekenen, laat de mat met het papier dan onaangeraakt in de Silhouette zitten. Verwijder de pen-houder met de pen en plaats de houder met het mes terug in de Silhouette. Ga verder met de volgende handelingen.

- Click opnieuw op de [Output Settings] icon.
- Ga naar het tabblad [Cutting Settings]
- Click op de knop [Cutline Settings]
- Vink de zwarte groep uit en zet de rode groep aan.
- Click op de knop [OK]
- Ga naar het tabblad [Print Settings]
- Zet de optie [Print Cut Lines] uit, want we willen nu echt gaan snijden en niet meer tekenen.
- Click op de knop [Output to Craft ROBO...] en gebruik dan de settings die je voor dit type papier altijd gebruikt.

Voila, in een handomdraai maak je (in mijn geval) een super leuke journalling card.


English explanation.

You need a file with at least two diffent colors of lines. I used a file with black lines and red lines.

- Open the file in ROBO Master and click on the [Output Settings] icon (it's the sixth icon from the left).
- Go to the tab-section called [Cutting Settings]
- Click on the button [Cutline Settings]

Now you see that there are two color available in this file. Black and red. I want the black lines drawed first.

- Opt-out the red section, so only the black section is checked.
- Click [OK]
- Go to the tab-section called [Print Settings]
- Check the options called [Print Cut Lines]

Now is the time to place your pen into the pen holder and put it in your Silhouette. Once you have done that, hit the power switch if it wasn't already on.

- Click on the button [Output to Craft ROBO...]

And here you get your usual screens about loading the driver and start cutting (or drawing for this matter).

- I set my speed on 1 and the thickness on 5, but I guess you have to play with that yourself to find a suitable setting to match your pen.
- Click on the button [Cut] and the Silhouette will do the drawing.

If it's finished your drawing, leave the mat with the paper untouched in your Silhouette and remove pen holder with the pen. Place the the blade holder with the blade back in your Silhouette and take the next steps.

- Click on the [Output Settings] icon again.
- Go to the tab-section called [Cutting Settings]
- Click on the button [Cutline Settings]
- Opt-out the black lines and check that the red lines are now opt-in.
- Click on the button [OK]
- Go to the tab-section called [Print Settings]
- Opt-out the options called [Print Cut Lines], because we actually want to cut right now.
- Click on the button [Output to Craft ROBO...] and set your usual settings for cutting with your paper.

Voila, you have your (in case of my example) a cute looking journalling card.

This technique has been seen 3078 times.



LAATSTE REAKTIES

thank you very much
(dom over freebee Wordart Little Boy op 11-04-2013 om 14:21)


thanks
(Marrian over freebee transport op 09-01-2013 om 22:49)


Ontzettend leuk!
(Anke over freebee spot flower op 06-12-2012 om 20:44)


I took three gift boxes and four other files and I'm so grateful for them! Thank you so much!
(Tina over freebee Koekjes zakje op 27-10-2012 om 12:03)


thankyou
(chris over freebee Happy birthday 1 op 15-09-2012 om 10:27)


thank you for your delighful files
(d blatch over freebee square bracket op 10-09-2012 om 11:39)


thank you for your delighful files
(d blatch over freebee scallopped figure 3 op 10-09-2012 om 11:38)


Thank you for sharing the clipart :-)
(Sue Miller over freebee ornaments op 28-08-2012 om 20:13)


thanks
(chrisj over freebee square bracket op 26-08-2012 om 21:10)


Thanks for lovely downloads, they will be very useful.
(Joy over freebee standing scallopped card op 14-08-2012 om 00:09)


 
     
Hinkeltje fotografie & scrapbooking   Gasthuisstraat 101   5171 GE   Kaatsheuvel   tel 0620765383   info@hinkeltje.com
kvk 18074949   SNS BANK 93.70.08.346   BTW nr NL1493.70.234.B01